dmesg - Intel Xeon E5450

Return To Intel Xeon E5450 System Information

Linux version 5.4.0-33-generic (buildd@lcy01-amd64-022) (gcc version 9.3.0 (Ubuntu 9.3.0-10ubuntu2)) #37-Ubuntu SMP Thu May 21 12:53:59 UTC 2020 (Ubuntu 5.4.0-33.37-generic 5.4.34)
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  Hygon HygonGenuine
  Centaur CentaurHauls
  zhaoxin   Shanghai  
x86/fpu: x87 FPU will use FXSAVE
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x00000000bff7ffff] usable
BIOS-e820: [mem 0x00000000bff80000-0x00000000bff8dfff] ACPI data
BIOS-e820: [mem 0x00000000bff8e000-0x00000000bffcffff] ACPI NVS
BIOS-e820: [mem 0x00000000bffd0000-0x00000000bfffffff] reserved
BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
BIOS-e820: [mem 0x0000000100000000-0x000000023fffffff] usable
NX (Execute Disable) protection: active
SMBIOS 2.5 present.
DMI: System manufacturer P5QL PRO/P5QL PRO, BIOS 1004    07/01/2009
tsc: Fast TSC calibration using PIT
tsc: Detected 3690.069 MHz processor
e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
e820: remove [mem 0x000a0000-0x000fffff] usable
last_pfn = 0x240000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-DFFFF write-protect
  E0000-EFFFF write-through
  F0000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 0000000000 mask 3E00000000 write-back
  1 base 0200000000 mask 3FC0000000 write-back
  2 base 00C0000000 mask 3FC0000000 uncachable
  3 disabled
  4 disabled
  5 disabled
  6 disabled
  7 disabled
x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
total RAM covered: 8192M
Found optimal setting for mtrr clean up
 gran_size: 64K 	chunk_size: 64K 	num_reg: 4  	lose cover RAM: 0G
e820: update [mem 0xc0000000-0xffffffff] usable ==> reserved
last_pfn = 0xbff80 max_arch_pfn = 0x400000000
found SMP MP-table at [mem 0x000ff780-0x000ff78f]
check: Scanning 1 areas for low memory corruption
BRK [0x1e8001000, 0x1e8001fff] PGTABLE
BRK [0x1e8002000, 0x1e8002fff] PGTABLE
BRK [0x1e8003000, 0x1e8003fff] PGTABLE
BRK [0x1e8004000, 0x1e8004fff] PGTABLE
BRK [0x1e8005000, 0x1e8005fff] PGTABLE
BRK [0x1e8006000, 0x1e8006fff] PGTABLE
BRK [0x1e8007000, 0x1e8007fff] PGTABLE
BRK [0x1e8008000, 0x1e8008fff] PGTABLE
RAMDISK: [mem 0x3219b000-0x350c4fff]
ACPI: Early table checksum verification disabled
ACPI: RSDP 0x00000000000FBB10 000014 (v00 ACPIAM)
ACPI: RSDT 0x00000000BFF80000 000040 (v01 A_M_I_ OEMRSDT  07000901 MSFT 00000097)
ACPI: FACP 0x00000000BFF80200 000084 (v02 A_M_I_ OEMFACP  07000901 MSFT 00000097)
ACPI: DSDT 0x00000000BFF80440 008888 (v01 A1014  A1014001 00000001 INTL 20060113)
ACPI: FACS 0x00000000BFF8E000 000040
ACPI: APIC 0x00000000BFF80390 00006C (v01 A_M_I_ OEMAPIC  07000901 MSFT 00000097)
ACPI: MCFG 0x00000000BFF80400 00003C (v01 A_M_I_ OEMMCFG  07000901 MSFT 00000097)
ACPI: OEMB 0x00000000BFF8E040 000081 (v01 A_M_I_ AMI_OEM  07000901 MSFT 00000097)
ACPI: HPET 0x00000000BFF88CD0 000038 (v01 A_M_I_ OEMHPET  07000901 MSFT 00000097)
ACPI: OSFR 0x00000000BFF88D10 0000B0 (v01 A_M_I_ OEMOSFR  07000901 MSFT 00000097)
ACPI: SSDT 0x00000000BFF8EAD0 000A7C (v01 DpgPmm CpuPm    00000012 INTL 20060113)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at [mem 0x0000000000000000-0x000000023fffffff]
NODE_DATA(0) allocated [mem 0x23ffd1000-0x23fffbfff]
Zone ranges:
  DMA      [mem 0x0000000000001000-0x0000000000ffffff]
  DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
  Normal   [mem 0x0000000100000000-0x000000023fffffff]
  Device   empty
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x0000000000001000-0x000000000009efff]
  node   0: [mem 0x0000000000100000-0x00000000bff7ffff]
  node   0: [mem 0x0000000100000000-0x000000023fffffff]
Zeroed struct page in unavailable ranges: 226 pages
Initmem setup node 0 [mem 0x0000000000001000-0x000000023fffffff]
On node 0 totalpages: 2096926
  DMA zone: 64 pages used for memmap
  DMA zone: 21 pages reserved
  DMA zone: 3998 pages, LIFO batch:0
  DMA32 zone: 12222 pages used for memmap
  DMA32 zone: 782208 pages, LIFO batch:63
  Normal zone: 20480 pages used for memmap
  Normal zone: 1310720 pages, LIFO batch:63
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a301 base: 0xfed00000
smpboot: Allowing 4 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
PM: Registered nosave memory: [mem 0xbff80000-0xbff8dfff]
PM: Registered nosave memory: [mem 0xbff8e000-0xbffcffff]
PM: Registered nosave memory: [mem 0xbffd0000-0xbfffffff]
PM: Registered nosave memory: [mem 0xc0000000-0xfedfffff]
PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
PM: Registered nosave memory: [mem 0xfee01000-0xffefffff]
PM: Registered nosave memory: [mem 0xfff00000-0xffffffff]
[mem 0xc0000000-0xfedfffff] available for PCI devices
Booting paravirtualized kernel on bare hardware
clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
percpu: Embedded 54 pages/cpu s184320 r8192 d28672 u524288
pcpu-alloc: s184320 r8192 d28672 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 
Built 1 zonelists, mobility grouping on.  Total pages: 2064139
Policy zone: Normal
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
mem auto-init: stack:off, heap alloc:on, heap free:off
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 8096116K/8387704K available (14339K kernel code, 2397K rwdata, 4948K rodata, 2712K init, 4992K bss, 291588K reserved, 0K cma-reserved)
random: get_random_u64 called from kmem_cache_open+0x2d/0x410 with crng_init=0
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Kernel/User page tables isolation: enabled
ftrace: allocating 44484 entries in 174 pages
rcu: Hierarchical RCU implementation.
rcu: 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
	Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16
vt handoff: transparent VT on vt#7
Console: colour dummy device 80x25
printk: console [tty0] enabled
ACPI: Core revision 20190816
clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
APIC: Switch to symmetric I/O mode setup
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x6a616061ba8, max_idle_ns: 881590584827 ns
Calibrating delay loop (skipped), value calculated using timer frequency.. 7380.13 BogoMIPS (lpj=14760276)
pid_max: default: 32768 minimum: 301
LSM: Security Framework initializing
Yama: becoming mindful.
AppArmor: AppArmor initialized
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
*** VALIDATE tmpfs ***
*** VALIDATE proc ***
*** VALIDATE cgroup1 ***
*** VALIDATE cgroup2 ***
mce: CPU0: Thermal monitoring enabled (TM2)
process: using mwait in idle threads
Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
Spectre V2 : Mitigation: Full generic retpoline
Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
Speculative Store Bypass: Vulnerable
MDS: Vulnerable: Clear CPU buffers attempted, no microcode
Freeing SMP alternatives memory: 40K
smpboot: CPU0: Intel(R) Xeon(R) CPU           E5450  @ 3.00GHz (family: 0x6, model: 0x17, stepping: 0x6)
Performance Events: PEBS fmt0+, Core2 events, 4-deep LBR, Intel PMU driver.
... version:                2
... bit width:              40
... generic registers:      2
... value mask:             000000ffffffffff
... max period:             000000007fffffff
... fixed-purpose events:   3
... event mask:             0000000700000003
rcu: Hierarchical SRCU implementation.
NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
smp: Bringing up secondary CPUs ...
x86: Booting SMP configuration:
.... node  #0, CPUs:      #1 #2 #3
smp: Brought up 1 node, 4 CPUs
smpboot: Max logical packages: 1
smpboot: Total of 4 processors activated (29520.55 BogoMIPS)
devtmpfs: initialized
x86/mm: Memory block size: 128MB
PM: Registering ACPI NVS region [mem 0xbff8e000-0xbffcffff] (270336 bytes)
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
pinctrl core: initialized pinctrl subsystem
PM: RTC time: 18:31:41, date: 2020-06-07
NET: Registered protocol family 16
audit: initializing netlink subsys (disabled)
audit: type=2000 audit(1591554700.148:1): state=initialized audit_enabled=0 res=1
EISA bus registered
cpuidle: using governor ladder
cpuidle: using governor menu
ACPI: bus type PCI registered
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI: Using configuration type 1 for base access
HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: Added _OSI(Linux-Dell-Video)
ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
ACPI: 2 ACPI AML tables successfully acquired and loaded
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF8EBF36114000 000277 (v01 DpgPmm P001Ist  00000011 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF8EBF36117400 000277 (v01 DpgPmm P002Ist  00000012 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF8EBF36116C00 000277 (v01 DpgPmm P003Ist  00000012 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF8EBF363DFC00 000277 (v01 DpgPmm P004Ist  00000012 INTL 20060113)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: Enabled 15 GPEs in block 00 to 3F
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window]
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: [8086:2e20] type 00 class 0x060000
pci 0000:00:00.0: DMAR: Disabling IOMMU for graphics on this chipset
pci 0000:00:00.0: DMAR: Forcing write-buffer flush capability
pci 0000:00:01.0: [8086:2e21] type 01 class 0x060400
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: [8086:3a37] type 00 class 0x0c0300
pci 0000:00:1a.0: reg 0x20: [io  0xb800-0xb81f]
pci 0000:00:1a.1: [8086:3a38] type 00 class 0x0c0300
pci 0000:00:1a.1: reg 0x20: [io  0xb880-0xb89f]
pci 0000:00:1a.2: [8086:3a39] type 00 class 0x0c0300
pci 0000:00:1a.2: reg 0x20: [io  0xbc00-0xbc1f]
pci 0000:00:1a.7: [8086:3a3c] type 00 class 0x0c0320
pci 0000:00:1a.7: reg 0x10: [mem 0xfe8ffc00-0xfe8fffff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: [8086:3a3e] type 00 class 0x040300
pci 0000:00:1b.0: reg 0x10: [mem 0xfe8f8000-0xfe8fbfff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: [8086:3a40] type 01 class 0x060400
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: [8086:3a48] type 01 class 0x060400
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: [8086:3a4a] type 01 class 0x060400
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: [8086:3a34] type 00 class 0x0c0300
pci 0000:00:1d.0: reg 0x20: [io  0xb080-0xb09f]
pci 0000:00:1d.1: [8086:3a35] type 00 class 0x0c0300
pci 0000:00:1d.1: reg 0x20: [io  0xb400-0xb41f]
pci 0000:00:1d.2: [8086:3a36] type 00 class 0x0c0300
pci 0000:00:1d.2: reg 0x20: [io  0xb480-0xb49f]
pci 0000:00:1d.7: [8086:3a3a] type 00 class 0x0c0320
pci 0000:00:1d.7: reg 0x10: [mem 0xfe8ff800-0xfe8ffbff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
pci 0000:00:1f.0: [8086:3a18] type 00 class 0x060100
pci 0000:00:1f.2: [8086:3a20] type 00 class 0x01018f
pci 0000:00:1f.2: reg 0x10: [io  0xa000-0xa007]
pci 0000:00:1f.2: reg 0x14: [io  0x9c00-0x9c03]
pci 0000:00:1f.2: reg 0x18: [io  0x9880-0x9887]
pci 0000:00:1f.2: reg 0x1c: [io  0x9800-0x9803]
pci 0000:00:1f.2: reg 0x20: [io  0x9480-0x948f]
pci 0000:00:1f.2: reg 0x24: [io  0x9400-0x940f]
pci 0000:00:1f.3: [8086:3a30] type 00 class 0x0c0500
pci 0000:00:1f.3: reg 0x10: [mem 0xfe8ff400-0xfe8ff4ff 64bit]
pci 0000:00:1f.3: reg 0x20: [io  0x0400-0x041f]
pci 0000:00:1f.5: [8086:3a26] type 00 class 0x010185
pci 0000:00:1f.5: reg 0x10: [io  0xb000-0xb007]
pci 0000:00:1f.5: reg 0x14: [io  0xac00-0xac03]
pci 0000:00:1f.5: reg 0x18: [io  0xa880-0xa887]
pci 0000:00:1f.5: reg 0x1c: [io  0xa800-0xa803]
pci 0000:00:1f.5: reg 0x20: [io  0xa480-0xa48f]
pci 0000:00:1f.5: reg 0x24: [io  0xa400-0xa40f]
pci 0000:01:00.0: [1002:67ff] type 00 class 0x030000
pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:01:00.0: reg 0x18: [mem 0xcfe00000-0xcfffffff 64bit pref]
pci 0000:01:00.0: reg 0x20: [io  0xc000-0xc0ff]
pci 0000:01:00.0: reg 0x24: [mem 0xfe980000-0xfe9bffff]
pci 0000:01:00.0: reg 0x30: [mem 0xfe9c0000-0xfe9dffff pref]
pci 0000:01:00.0: enabling Extended Tags
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:01:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 5 GT/s x8 link at 0000:00:01.0 (capable of 63.008 Gb/s with 8 GT/s x8 link)
pci 0000:01:00.1: [1002:aae0] type 00 class 0x040300
pci 0000:01:00.1: reg 0x10: [mem 0xfe9fc000-0xfe9fffff 64bit]
pci 0000:01:00.1: enabling Extended Tags
pci 0000:01:00.1: supports D1 D2
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
pci 0000:00:01.0:   bridge window [mem 0xfe900000-0xfe9fffff]
pci 0000:00:01.0:   bridge window [mem 0xcfe00000-0xdfffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 04]
pci 0000:00:1c.0:   bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
pci 0000:03:00.0: [11ab:6101] type 00 class 0x01018f
pci 0000:03:00.0: reg 0x10: [io  0xec00-0xec07]
pci 0000:03:00.0: reg 0x14: [io  0xe880-0xe883]
pci 0000:03:00.0: reg 0x18: [io  0xe800-0xe807]
pci 0000:03:00.0: reg 0x1c: [io  0xe480-0xe483]
pci 0000:03:00.0: reg 0x20: [io  0xe400-0xe40f]
pci 0000:03:00.0: reg 0x24: [mem 0xfebffc00-0xfebffdff]
pci 0000:03:00.0: supports D1
pci 0000:03:00.0: PME# supported from D0 D1 D3hot
pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.4: PCI bridge to [bus 03]
pci 0000:00:1c.4:   bridge window [io  0xe000-0xefff]
pci 0000:00:1c.4:   bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:02:00.0: [1969:1026] type 00 class 0x020000
pci 0000:02:00.0: reg 0x10: [mem 0xfeac0000-0xfeafffff 64bit]
pci 0000:02:00.0: reg 0x18: [io  0xdc00-0xdc7f]
pci 0000:02:00.0: PME# supported from D3hot D3cold
pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.5: PCI bridge to [bus 02]
pci 0000:00:1c.5:   bridge window [io  0xd000-0xdfff]
pci 0000:00:1c.5:   bridge window [mem 0xfea00000-0xfeafffff]
pci_bus 0000:05: extended config space not accessible
pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive decode)
pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0xc0000000-0xffffffff window] (subtractive decode)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
iommu: Default domain type: Translated 
SCSI subsystem initialized
libata version 3.00 loaded.
pci 0000:01:00.0: vgaarb: setting as boot VGA device
pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
pci 0000:01:00.0: vgaarb: bridge control possible
vgaarb: loaded
ACPI: bus type USB registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
PTP clock support registered
EDAC MC: Ver: 3.0.0
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
e820: reserve RAM buffer [mem 0xbff80000-0xbfffffff]
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
NetLabel:  unlabeled traffic allowed by default
hpet: 4 channels of 0 reserved for per-cpu timers
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 comparators, 64-bit 14.318180 MHz counter
clocksource: Switched to clocksource tsc-early
*** VALIDATE bpf ***
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
*** VALIDATE ramfs ***
*** VALIDATE hugetlbfs ***
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
system 00:00: [mem 0xfed14000-0xfed19fff] has been reserved
system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:02: [dma 2]
pnp 00:02: Plug and Play ACPI device, IDs PNP0700 (active)
system 00:03: [io  0x0290-0x029f] has been reserved
system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:04: [io  0x04d0-0x04d1] has been reserved
system 00:04: [io  0x0800-0x087f] has been reserved
system 00:04: [io  0x0500-0x057f] has been reserved
system 00:04: [mem 0xfed08000-0xfed08fff] has been reserved
system 00:04: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:04: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:04: [mem 0xfed50000-0xfed8ffff] has been reserved
system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:05: [mem 0xffc00000-0xffefffff] has been reserved
system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:07: [dma 0 disabled]
pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
system 00:08: [mem 0xe0000000-0xefffffff] has been reserved
system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:09: [mem 0x000c0000-0x000cffff] could not be reserved
system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:09: [mem 0x00100000-0xbfffffff] could not be reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 10 devices
thermal_sys: Registered thermal governor 'fair_share'
thermal_sys: Registered thermal governor 'bang_bang'
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
thermal_sys: Registered thermal governor 'power_allocator'
clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 04] add_size 1000
pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 04] add_size 400000 add_align 100000
pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
pci 0000:00:1c.5: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
pci 0000:00:1c.0: BAR 14: assigned [mem 0xc0000000-0xc03fffff]
pci 0000:00:1c.4: BAR 15: assigned [mem 0xc0400000-0xc05fffff 64bit pref]
pci 0000:00:1c.5: BAR 15: assigned [mem 0xc0600000-0xc07fffff 64bit pref]
pci 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
pci 0000:00:01.0:   bridge window [mem 0xfe900000-0xfe9fffff]
pci 0000:00:01.0:   bridge window [mem 0xcfe00000-0xdfffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 04]
pci 0000:00:1c.0:   bridge window [io  0x1000-0x1fff]
pci 0000:00:1c.0:   bridge window [mem 0xc0000000-0xc03fffff]
pci 0000:00:1c.0:   bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
pci 0000:00:1c.4: PCI bridge to [bus 03]
pci 0000:00:1c.4:   bridge window [io  0xe000-0xefff]
pci 0000:00:1c.4:   bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:00:1c.4:   bridge window [mem 0xc0400000-0xc05fffff 64bit pref]
pci 0000:00:1c.5: PCI bridge to [bus 02]
pci 0000:00:1c.5:   bridge window [io  0xd000-0xdfff]
pci 0000:00:1c.5:   bridge window [mem 0xfea00000-0xfeafffff]
pci 0000:00:1c.5:   bridge window [mem 0xc0600000-0xc07fffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 05]
pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window]
pci_bus 0000:00: resource 8 [mem 0xc0000000-0xffffffff window]
pci_bus 0000:01: resource 0 [io  0xc000-0xcfff]
pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff]
pci_bus 0000:01: resource 2 [mem 0xcfe00000-0xdfffffff 64bit pref]
pci_bus 0000:04: resource 0 [io  0x1000-0x1fff]
pci_bus 0000:04: resource 1 [mem 0xc0000000-0xc03fffff]
pci_bus 0000:04: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
pci_bus 0000:03: resource 0 [io  0xe000-0xefff]
pci_bus 0000:03: resource 1 [mem 0xfeb00000-0xfebfffff]
pci_bus 0000:03: resource 2 [mem 0xc0400000-0xc05fffff 64bit pref]
pci_bus 0000:02: resource 0 [io  0xd000-0xdfff]
pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
pci_bus 0000:02: resource 2 [mem 0xc0600000-0xc07fffff 64bit pref]
pci_bus 0000:05: resource 4 [io  0x0000-0x0cf7 window]
pci_bus 0000:05: resource 5 [io  0x0d00-0xffff window]
pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff window]
pci_bus 0000:05: resource 7 [mem 0x000d0000-0x000dffff window]
pci_bus 0000:05: resource 8 [mem 0xc0000000-0xffffffff window]
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
TCP: Hash tables configured (established 65536 bind 65536)
UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
NET: Registered protocol family 1
NET: Registered protocol family 44
pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
pci 0000:01:00.1: D0 power state depends on 0000:01:00.0
PCI: CLS 32 bytes, default 64
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 48296K
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB: mapped [mem 0xbbf80000-0xbff80000] (64MB)
check: Scanning for low memory corruption every 60 seconds
Initialise system trusted keyrings
Key type blacklist registered
workingset: timestamp_bits=36 max_order=21 bucket_order=0
zbud: loaded
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse: init (API version 7.31)
*** VALIDATE fuse ***
*** VALIDATE fuse ***
Platform Keyring initialized
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
io scheduler mq-deadline registered
pcieport 0000:00:1c.0: enabling device (0106 -> 0107)
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
vesafb: mode is 1920x1080x32, linelength=7680, pages=0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
vesafb: framebuffer at 0xd0000000, mapped to 0x(____ptrval____), using 8128k, total 8128k
fbcon: Deferring console take-over
fb0: VESA VGA frame buffer device
intel_idle: does not run on family 6 model 23
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
00:07: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
Linux agpgart interface v0.103
loop: module loaded
ata_piix 0000:00:1f.2: version 2.13
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
scsi host0: ata_piix
scsi host1: ata_piix
ata1: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19
ata2: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
scsi host2: ata_piix
scsi host3: ata_piix
ata3: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 19
ata4: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 19
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
PPP generic driver version 2.4.2
VFIO - User Level meta-driver version: 0.3
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:1a.7: EHCI Host Controller
ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:1a.7: debug port 1
ehci-pci 0000:00:1a.7: cache line size of 32 is not supported
ehci-pci 0000:00:1a.7: irq 18, io mem 0xfe8ffc00
ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 5.4.0-33-generic ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci-pci 0000:00:1d.7: EHCI Host Controller
ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci-pci 0000:00:1d.7: debug port 1
ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
ehci-pci 0000:00:1d.7: irq 23, io mem 0xfe8ff800
ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 5.4.0-33-generic ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-platform: OHCI generic platform driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: detected 2 ports
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.04
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 5.4.0-33-generic uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: detected 2 ports
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.04
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 5.4.0-33-generic uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: detected 2 ports
uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000bc00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.04
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 5.4.0-33-generic uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: detected 2 ports
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b080
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.04
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 5.4.0-33-generic uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: detected 2 ports
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b400
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.04
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 5.4.0-33-generic uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: detected 2 ports
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b480
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.04
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 5.4.0-33-generic uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
i8042: PNP: No PS/2 controller found.
i8042: Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:01: RTC can wake from S4
rtc_cmos 00:01: registered as rtc0
rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
i2c /dev entries driver
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com
platform eisa.0: Probing EISA bus 0
platform eisa.0: EISA: Cannot allocate resource for mainboard
platform eisa.0: Cannot allocate resource for EISA slot 1
platform eisa.0: Cannot allocate resource for EISA slot 2
platform eisa.0: Cannot allocate resource for EISA slot 3
platform eisa.0: Cannot allocate resource for EISA slot 4
platform eisa.0: Cannot allocate resource for EISA slot 5
platform eisa.0: Cannot allocate resource for EISA slot 6
platform eisa.0: Cannot allocate resource for EISA slot 7
platform eisa.0: Cannot allocate resource for EISA slot 8
platform eisa.0: EISA: Detected 0 cards
intel_pstate: CPU model not supported
ledtrig-cpu: registered to indicate activity on CPUs
drop_monitor: Initializing network drop monitor service
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
Key type dns_resolver registered
RAS: Correctable Errors collector initialized.
microcode: sig=0x10676, pf=0x40, revision=0x60f
microcode: Microcode Update Driver: v2.2.
IPI shorthand broadcast: enabled
sched_clock: Marking stable (642737578, 150679)->(666012376, -23124119)
registered taskstats version 1
Loading compiled-in X.509 certificates
Loaded X.509 cert 'Build time autogenerated kernel key: c329bf6a4b0ec867054f21d6ed1bd5cc94d1739c'
zswap: loaded using pool lzo/zbud
Key type ._fscrypt registered
Key type .fscrypt registered
Key type big_key registered
Key type encrypted registered
AppArmor: AppArmor sha1 policy hashing enabled
ima: No TPM chip found, activating TPM-bypass!
ima: Allocated hash algorithm: sha1
ima: No architecture policies found
evm: Initialising EVM extended attributes:
evm: security.selinux
evm: security.SMACK64
evm: security.SMACK64EXEC
evm: security.SMACK64TRANSMUTE
evm: security.SMACK64MMAP
evm: security.apparmor
evm: security.ima
evm: security.capability
evm: HMAC attrs: 0x1
PM:   Magic number: 8:911:543
rtc_cmos 00:01: setting system clock to 2020-06-07T18:31:41 UTC (1591554701)
ata4: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
usb 6-2: new full-speed USB device number 2 using uhci_hcd
ata1.00: SATA link down (SStatus 0 SControl 300)
ata1.01: SATA link down (SStatus 0 SControl 300)
usb 6-2: New USB device found, idVendor=045e, idProduct=0745, bcdDevice= 6.33
usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 6-2: Product: Microsoft® 2.4GHz Transceiver v7.0
usb 6-2: Manufacturer: Microsoft
ata2.00: SATA link down (SStatus 0 SControl 300)
ata2.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.01: ATA-8: TOSHIBA MK8052GSX, LV010A, max UDMA/100
ata2.01: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.01: configured for UDMA/100
scsi 1:0:1:0: Direct-Access     ATA      TOSHIBA MK8052GS 0A   PQ: 0 ANSI: 5
sd 1:0:1:0: Attached scsi generic sg0 type 0
sd 1:0:1:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 1:0:1:0: [sda] Write Protect is off
sd 1:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 >
sd 1:0:1:0: [sda] Attached SCSI disk
Freeing unused decrypted memory: 2040K
Freeing unused kernel image memory: 2712K
Write protecting the kernel read-only data: 22528k
Freeing unused kernel image memory: 2008K
Freeing unused kernel image memory: 1196K
x86/mm: Checked W+X mappings: passed, no W+X pages found.
x86/mm: Checking user space page tables
x86/mm: Checked W+X mappings: passed, no W+X pages found.
Run /init as init process
tsc: Refined TSC clocksource calibration: 3689.960 MHz
clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x6a6093ef227, max_idle_ns: 881590875302 ns
clocksource: Switched to clocksource tsc
Floppy drive(s): fd0 is 1.44M
scsi host4: pata_marvell
scsi host5: pata_marvell
ata5: PATA max UDMA/100 cmd 0xec00 ctl 0xe880 bmdma 0xe400 irq 16
ata6: DUMMY
hidraw: raw HID events driver (C) Jiri Kosina
ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000084F (\PMRG) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPS0) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPS0) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
lpc_ich: Resource conflict(s) found affecting gpio_ich
ACPI Warning: SystemIO range 0x0000000000000400-0x000000000000041F conflicts with OpRegion 0x0000000000000400-0x000000000000040F (\SMRG) (20190816/utaddress-204)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
FDC 0 is a post-1991 82077
input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/0003:045E:0745.0001/input/input5
ATL1E 0000:02:00.0 enp2s0: renamed from eth0
hid-generic 0003:045E:0745.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Microsoft® 2.4GHz Transceiver v7.0] on usb-0000:00:1d.0-2/input0
input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/0003:045E:0745.0002/input/input6
input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 Consumer Control as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/0003:045E:0745.0002/input/input7
hid-generic 0003:045E:0745.0002: input,hidraw1: USB HID v1.11 Mouse [Microsoft Microsoft® 2.4GHz Transceiver v7.0] on usb-0000:00:1d.0-2/input1
input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 Consumer Control as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.2/0003:045E:0745.0003/input/input8
input: Microsoft Microsoft® 2.4GHz Transceiver v7.0 System Control as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.2/0003:045E:0745.0003/input/input10
hid-generic 0003:045E:0745.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Microsoft Microsoft® 2.4GHz Transceiver v7.0] on usb-0000:00:1d.0-2/input2
usb 7-2: new full-speed USB device number 2 using uhci_hcd
usb 7-2: device descriptor read/64, error -71
usb 7-2: device descriptor read/64, error -71
usb 7-2: new full-speed USB device number 3 using uhci_hcd
random: fast init done
usb 7-2: device descriptor read/64, error -71
fbcon: Taking over console
Console: switching to colour frame buffer device 240x67
random: systemd-udevd: uninitialized urandom read (16 bytes read)
random: systemd-udevd: uninitialized urandom read (16 bytes read)
random: systemd-udevd: uninitialized urandom read (16 bytes read)
EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
usb 7-2: device descriptor read/64, error -71
usb usb7-port2: attempt power cycle
usb usb7-port2: failed to disable port power
usb 7-2: new full-speed USB device number 4 using uhci_hcd
usb 7-2: device not accepting address 4, error -71
usb 7-2: new full-speed USB device number 5 using uhci_hcd
usb 7-2: device not accepting address 5, error -71
usb usb7-port2: unable to enumerate USB device
systemd[1]: Inserted module 'autofs4'
urandom_read: 3 callbacks suppressed
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: systemd 245.4-4ubuntu3 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
systemd[1]: Detected architecture x86-64.
random: systemd: uninitialized urandom read (16 bytes read)
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Set hostname to .
systemd[1]: Initializing machine ID from random generator.
systemd[1]: Installed transient /etc/machine-id file.
random: crng init done
random: 1 urandom warning(s) missed due to ratelimiting
systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
systemd[1]: Created slice system-modprobe.slice.
systemd[1]: Created slice system-systemd\x2dfsck.slice.
systemd[1]: Created slice User and Session Slice.
systemd[1]: Started Forward Password Requests to Wall Directory Watch.
systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
systemd[1]: Reached target User and Group Name Lookups.
systemd[1]: Reached target Remote File Systems.
systemd[1]: Reached target Slices.
systemd[1]: Listening on Syslog Socket.
systemd[1]: Listening on fsck to fsckd communication Socket.
systemd[1]: Listening on initctl Compatibility Named Pipe.
systemd[1]: Listening on Journal Audit Socket.
systemd[1]: Listening on Journal Socket (/dev/log).
systemd[1]: Listening on Journal Socket.
systemd[1]: Listening on udev Control Socket.
systemd[1]: Listening on udev Kernel Socket.
systemd[1]: Mounting Huge Pages File System...
systemd[1]: Mounting POSIX Message Queue File System...
systemd[1]: Mounting Kernel Debug File System...
systemd[1]: Mounting Kernel Trace File System...
systemd[1]: Starting Journal Service...
systemd[1]: Starting Set the console keyboard layout...
systemd[1]: Starting Create list of static device nodes for the current kernel...
systemd[1]: Starting Load Kernel Module drm...
systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
systemd[1]: Starting Load Kernel Modules...
systemd[1]: Starting Remount Root and Kernel File Systems...
systemd[1]: Starting udev Coldplug all Devices...
systemd[1]: Starting Uncomplicated firewall...
systemd[1]: Finished Create list of static device nodes for the current kernel.
systemd[1]: Mounted Huge Pages File System.
systemd[1]: Mounted POSIX Message Queue File System.
systemd[1]: Mounted Kernel Debug File System.
systemd[1]: Mounted Kernel Trace File System.
EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
systemd[1]: Finished Remount Root and Kernel File Systems.
systemd[1]: Activating swap /swapfile...
systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
systemd[1]: Starting Load/Save Random Seed...
systemd[1]: Starting Create System Users...
systemd[1]: Finished Uncomplicated firewall.
systemd[1]: modprobe@drm.service: Succeeded.
systemd[1]: Finished Load Kernel Module drm.
Adding 2097148k swap on /swapfile.  Priority:-2 extents:6 across:2260988k FS
systemd[1]: Activated swap /swapfile.
systemd[1]: Reached target Swap.
systemd[1]: Finished Set the console keyboard layout.
systemd[1]: Started Journal Service.
systemd-journald[317]: Received client request to flush runtime journal.
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
intel_powerclamp: No package C-state available
intel_powerclamp: No package C-state available
intel_powerclamp: No package C-state available
intel_powerclamp: No package C-state available
AMD-Vi: AMD IOMMUv2 driver by Joerg Roedel 
AMD-Vi: AMD IOMMUv2 functionality not available on this system
[drm] amdgpu kernel modesetting enabled.
CRAT table not found
Virtual CRAT table created for CPU
Parsing CRAT table with 1 nodes
Creating topology SYSFS entries
Topology: Add CPU node
Finished initializing topology
amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 0: 0xd0000000 -> 0xdfffffff
amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 2: 0xcfe00000 -> 0xcfffffff
amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 5: 0xfe980000 -> 0xfe9bffff
checking generic (d0000000 7f0000) vs hw (d0000000 10000000)
fb0: switching to amdgpudrmfb from VESA VGA
Console: switching to colour dummy device 80x25
amdgpu 0000:01:00.0: vgaarb: deactivate vga console
[drm] initializing kernel modesetting (POLARIS11 0x1002:0x67FF 0x1458:0x22FF 0xCF).
[drm] register mmio base: 0xFE980000
[drm] register mmio size: 262144
[drm] PCIE atomic ops is not supported
[drm] add ip block number 0 
[drm] add ip block number 1 
[drm] add ip block number 2 
[drm] add ip block number 3 
[drm] add ip block number 4 
[drm] add ip block number 5 
[drm] add ip block number 6 
[drm] add ip block number 7 
[drm] add ip block number 8 
kfd kfd: skipped device 1002:67ff, PCI rejects atomics
resource sanity check: requesting [mem 0x000c0000-0x000dffff], which spans more than PCI Bus 0000:00 [mem 0x000d0000-0x000dffff window]
caller pci_map_rom+0x71/0x18c mapping multiple BARs
amdgpu 0000:01:00.0: No more image in the PCI ROM
ATOM BIOS: xxx-xxx-xxx
[drm] UVD is enabled in VM mode
[drm] UVD ENC is enabled in VM mode
[drm] VCE enabled in VM mode
[drm] vm size is 64 GB, 2 levels, block size is 10-bit, fragment size is 9-bit
snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
snd_hda_intel 0000:01:00.1: Force to non-snoop mode
input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input11
input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input12
input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13
input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
amdgpu 0000:01:00.0: VRAM: 4096M 0x000000F400000000 - 0x000000F4FFFFFFFF (4096M used)
amdgpu 0000:01:00.0: GART: 256M 0x000000FF00000000 - 0x000000FF0FFFFFFF
[drm] Detected VRAM RAM=4096M, BAR=256M
[drm] RAM width 128bits GDDR5
[TTM] Zone  kernel: Available graphics memory: 4076204 KiB
[TTM] Zone   dma32: Available graphics memory: 2097152 KiB
[TTM] Initializing pool allocator
[TTM] Initializing DMA pool allocator
[drm] amdgpu: 4096M of VRAM memory ready
[drm] amdgpu: 4096M of GTT memory ready.
[drm] GART: num cpu pages 65536, num gpu pages 65536
[drm] PCIE GART of 256M enabled (table at 0x000000F4007E9000).
[drm] Chained IB support enabled!
snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC1200: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
snd_hda_codec_realtek hdaudioC0D0:    dig-out=0x11/0x1e
snd_hda_codec_realtek hdaudioC0D0:    inputs:
snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x19
snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x18
snd_hda_codec_realtek hdaudioC0D0:      Line=0x1a
input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18
input: HDA Intel Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input19
input: HDA Intel Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input20
input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input21
input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input22
input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input23
amdgpu: [powerplay] hwmgr_sw_init smu backed is polaris10_smu
[drm] Found UVD firmware Version: 1.130 Family ID: 16
[drm] Found VCE firmware Version: 53.26 Binary ID: 3
[drm] DM_PPLIB: values for Engine clock
[drm] DM_PPLIB:	 214000
[drm] DM_PPLIB:	 387000
[drm] DM_PPLIB:	 843000
[drm] DM_PPLIB:	 995000
[drm] DM_PPLIB:	 1062000
[drm] DM_PPLIB:	 1108000
[drm] DM_PPLIB:	 1149000
[drm] DM_PPLIB:	 1224000
[drm] DM_PPLIB: Validation clocks:
[drm] DM_PPLIB:    engine_max_clock: 122400
[drm] DM_PPLIB:    memory_max_clock: 175000
[drm] DM_PPLIB:    level           : 8
[drm] DM_PPLIB: values for Memory clock
[drm] DM_PPLIB:	 300000
[drm] DM_PPLIB:	 625000
[drm] DM_PPLIB:	 1750000
[drm] DM_PPLIB: Validation clocks:
[drm] DM_PPLIB:    engine_max_clock: 122400
[drm] DM_PPLIB:    memory_max_clock: 175000
[drm] DM_PPLIB:    level           : 8
[drm] Display Core initialized with v3.2.48!
snd_hda_intel 0000:01:00.1: bound 0000:01:00.0 (ops amdgpu_dm_audio_component_bind_ops [amdgpu])
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
[drm] UVD and UVD ENC initialized successfully.
[drm] VCE initialized successfully.
[drm] fb mappable at 0xD0D19000
[drm] vram apper at 0xD0000000
[drm] size 8294400
[drm] fb depth is 24
[drm]    pitch is 7680
fbcon: amdgpudrmfb (fb0) is primary device
Console: switching to colour frame buffer device 240x67
amdgpu 0000:01:00.0: fb0: amdgpudrmfb frame buffer device
[drm] Initialized amdgpu 3.35.0 20150101 for 0000:01:00.0 on minor 0
audit: type=1400 audit(1591554720.850:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=581 comm="apparmor_parser"
audit: type=1400 audit(1591554720.898:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ippusbxd" pid=583 comm="apparmor_parser"
audit: type=1400 audit(1591554720.898:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=580 comm="apparmor_parser"
audit: type=1400 audit(1591554720.962:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=587 comm="apparmor_parser"
audit: type=1400 audit(1591554721.098:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/tcpdump" pid=582 comm="apparmor_parser"
audit: type=1400 audit(1591554721.198:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=591 comm="apparmor_parser"
audit: type=1400 audit(1591554721.214:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=590 comm="apparmor_parser"
audit: type=1400 audit(1591554721.326:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=593 comm="apparmor_parser"
audit: type=1400 audit(1591554721.338:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=593 comm="apparmor_parser"
audit: type=1400 audit(1591554721.386:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=586 comm="apparmor_parser"
kauditd_printk_skb: 16 callbacks suppressed
audit: type=1400 audit(1591554725.910:28): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-soffice" pid=579 comm="apparmor_parser"
audit: type=1400 audit(1591554725.914:29): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-soffice//gpg" pid=579 comm="apparmor_parser"
audit: type=1400 audit(1591554738.210:30): apparmor="DENIED" operation="capable" profile="/usr/sbin/cups-browsed" pid=719 comm="cups-browsed" capability=23  capname="sys_nice"
ATL1E 0000:02:00.0 enp2s0: NIC Link is Up 
IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready
audit: type=1400 audit(1591554802.410:31): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/snap/snapd/7264/usr/lib/snapd/snap-confine" pid=1429 comm="apparmor_parser"
audit: type=1400 audit(1591554802.410:32): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/snap/snapd/7264/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=1429 comm="apparmor_parser"
rfkill: input handler disabled
rfkill: input handler enabled
rfkill: input handler disabled
audit: type=1400 audit(1591554921.774:33): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap-update-ns.snap-store" pid=3129 comm="apparmor_parser"
audit: type=1400 audit(1591554921.790:34): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.snap-store.snap-store" pid=3130 comm="apparmor_parser"
audit: type=1400 audit(1591554921.794:35): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.snap-store.ubuntu-software" pid=3131 comm="apparmor_parser"
audit: type=1400 audit(1591554921.798:36): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.snap-store.ubuntu-software-local-file" pid=3132 comm="apparmor_parser"
audit: type=1400 audit(1591554943.283:37): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/snap/snapd/7264/usr/lib/snapd/snap-confine" pid=3286 comm="apparmor_parser"
audit: type=1400 audit(1591554943.311:38): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/snap/snapd/7264/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=3286 comm="apparmor_parser"
audit: type=1400 audit(1591554943.791:39): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.snap-store.ubuntu-software-local-file" pid=3291 comm="apparmor_parser"
audit: type=1400 audit(1591554943.871:40): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.snap-store.ubuntu-software" pid=3290 comm="apparmor_parser"
audit: type=1400 audit(1591554943.875:41): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.snap-store.snap-store" pid=3289 comm="apparmor_parser"
audit: type=1400 audit(1591554944.131:42): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap-update-ns.snap-store" pid=3288 comm="apparmor_parser"
perf: interrupt took too long (2512 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
perf: interrupt took too long (3142 > 3140), lowering kernel.perf_event_max_sample_rate to 63500
audit: type=1400 audit(1591555572.938:43): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="lsb_release" pid=9631 comm="apparmor_parser"
audit: type=1400 audit(1591555572.998:44): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="nvidia_modprobe" pid=9634 comm="apparmor_parser"
audit: type=1400 audit(1591555572.998:45): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="nvidia_modprobe//kmod" pid=9634 comm="apparmor_parser"
audit: type=1400 audit(1591555573.846:46): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="lsb_release" pid=9735 comm="apparmor_parser"
audit: type=1400 audit(1591555573.886:47): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="libreoffice-xpdfimport" pid=9736 comm="apparmor_parser"
audit: type=1400 audit(1591555573.898:48): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="ippusbxd" pid=9738 comm="apparmor_parser"
audit: type=1400 audit(1591555573.926:49): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="libreoffice-senddoc" pid=9741 comm="apparmor_parser"
audit: type=1400 audit(1591555574.018:50): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/tcpdump" pid=9737 comm="apparmor_parser"
audit: type=1400 audit(1591555574.042:51): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cups-browsed" pid=9743 comm="apparmor_parser"
audit: type=1400 audit(1591555574.042:52): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="nvidia_modprobe" pid=9746 comm="apparmor_parser"
kauditd_printk_skb: 19 callbacks suppressed
audit: type=1400 audit(1591555578.682:72): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="libreoffice-soffice" pid=9734 comm="apparmor_parser"
audit: type=1400 audit(1591555578.702:73): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="libreoffice-soffice//gpg" pid=9734 comm="apparmor_parser"
audit: type=1400 audit(1591555578.746:74): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="libreoffice-xpdfimport" pid=9757 comm="apparmor_parser"
audit: type=1400 audit(1591555578.746:75): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="lsb_release" pid=9756 comm="apparmor_parser"
audit: type=1400 audit(1591555578.746:76): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="/usr/sbin/tcpdump" pid=9758 comm="apparmor_parser"
audit: type=1400 audit(1591555578.746:77): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="ippusbxd" pid=9759 comm="apparmor_parser"
audit: type=1400 audit(1591555578.746:78): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="libreoffice-senddoc" pid=9762 comm="apparmor_parser"
audit: type=1400 audit(1591555578.746:79): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="/usr/sbin/cups-browsed" pid=9763 comm="apparmor_parser"
audit: type=1400 audit(1591555578.750:80): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=9761 comm="apparmor_parser"
audit: type=1400 audit(1591555578.750:81): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=9761 comm="apparmor_parser"
kauditd_printk_skb: 20 callbacks suppressed
audit: type=1400 audit(1591555603.704:102): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=13575 comm="apparmor_parser"
audit: type=1400 audit(1591555603.704:103): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=13575 comm="apparmor_parser"
audit: type=1400 audit(1591555603.720:104): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd//third_party" pid=13575 comm="apparmor_parser"
audit: type=1400 audit(1591555605.324:105): apparmor="DENIED" operation="capable" profile="/usr/sbin/cups-browsed" pid=13688 comm="cups-browsed" capability=23  capname="sys_nice"
systemd[1]: systemd 245.4-4ubuntu3.1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
systemd[1]: Detected architecture x86-64.
systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
systemd[1]: Stopping Journal Service...
systemd-journald[317]: Received SIGTERM from PID 1 (systemd).
systemd[1]: systemd-journald.service: Succeeded.
systemd[1]: Stopped Journal Service.
systemd[1]: Starting Journal Service...
systemd[1]: Started Journal Service.
systemd-journald[14157]: Received client request to flush runtime journal.
perf: interrupt took too long (3930 > 3927), lowering kernel.perf_event_max_sample_rate to 50750
capability: warning: `gvfsd-admin' uses 32-bit capabilities (legacy support in use)

Return To Intel Xeon E5450 System Information